E-Archive

Cover Page

in Vol. 12 - November Issue - Year 2011
How to Save Money, Time and Energy on Dust Collection
This photo is of a blasting application that falls under the new Metal Fabrication Hazardous Air Pollutants (MFHAP) regulation. The collector has HemiPleat

This photo is of a blasting application that falls under the new Metal Fabrication Hazardous Air Pollutants (MFHAP) regulation. The collector has HemiPleat

Figure 1: Dust collector filter total cost of ownership sample data collection worksheet

Figure 1: Dust collector filter total cost of ownership sample data collection worksheet

Filter A: Dimple pleat media

Filter A: Dimple pleat media

Filter B: Open pleat close-up

Filter B: Open pleat close-up

Figure 2: New dust collector TCO example. Projected total cost of ownership savings for 16-cartridge dust collector using Filter B 8760 operating hours (one year)

Figure 2: New dust collector TCO example. Projected total cost of ownership savings for 16-cartridge dust collector using Filter B 8760 operating hours (one year)

Figure 3: Existing dust collector TCO example. Total cost of ownership comparison dust collector replacement Filter A vs. Filter B actual savings over 16 months (5,280 hours)

Figure 3: Existing dust collector TCO example. Total cost of ownership comparison dust collector replacement Filter A vs. Filter B actual savings over 16 months (5,280 hours)

Choosing the right cartridge filters can have a big impact on cost and performance. Camfil Farr APC is a leading manufacturer of dust collection equipment and a member of Camfil Farr, the largest air filter manufacturer in the world.

When it comes to choosing filters for a cartridge dust collector, plant engineers and maintenance professionals sometimes regard these items as more or less of a commodity. If Filter A and Filter B both offer the same rated efficiency and fill any special requirements – say, for example, the need for fire retardant media – then the lowest-priced filter would appear to be the better choice. In fact, the opposite may be true. However, this requires a "Total Cost of Ownership" (TCO) calculation to know for certain. TCO helps you determine what it really costs to own your dust collector filters… and how to save money, time and energy by choosing the best filters for your application.

Before starting your cost evaluation, it is important to make sure the filters you are considering for purchase will have adequate filtration efficiency and other characteristics needed to perform their primary function of air pollution control. OSHA has established permissible exposure limits (PEL) for hundreds of dusts ranging from nonspecific or "nuisance" dust to highly toxic substances. These limits are based on 8-hour time weighted average (TWA) exposure. Further information on PELs can be found at www.osha.gov/SLTC/pel.

For some dusts such as hexavalent chromium, a known carcinogen, OSHA has set thresholds as low as 5 micrograms (0.005 milligram) per cubic meter TWA. This is 10 times stricter than the limits for some other toxic dusts. Dust collectors need to be equipped with very high efficiency filtration media to meet such requirements. In addition, the EPA is implementing a strict new regulation on Metal Fabrication Hazardous Air Pollutants (MFHAP) that will no longer allow plants in nine metal fabricating and finishing source categories to exhaust contaminated air outside. The new MFHAP emissions requirements may again require many plants to incorporate high efficiency filtration to ensure compliance.

How do you know if your dust collector filters will comply with emission thresholds? The equipment supplier should provide a written guarantee stating the maximum emissions rate for the equipment over an 8-hour TWA. Filter efficiency stated as a percentage is not an acceptable substitute, even if the supplier promises 99.9 percent efficiency. OSHA and the EPA only cares that the quantified amount of dust in the air is below established limits.

Also, what are the size(s) and shape(s) of the dust particles to be collected? Is the dust combustible? Is it sticky or dry? These are just some of the characteristics that will also determine the best filter choice. Testing a sample of your dust is the only way to get an accurate picture of its properties. Dust testing is available from independent laboratories and many equipment suppliers.

How much does a filter really cost?

Let us assume you have identified the dust characteristics through testing, determined the required filtration efficiency, and narrowed the choice to two products with the same rated efficiency, Filter A and Filter B. Total cost of ownership (TCO) can now be applied to help you decide what filter to select. Similar in concept to life-cycle costing, TCO incorporates a step-by-step evaluation process encompassing three categories:

• Energy: The amount of energy required to operate the dust collector from day to day, including electrical costs, compressed air usage and CO2 emissions.
• Consumables: The items that are replaced periodically throughout the life of the equipment.
• Maintenance and Disposal: The time it takes to service the equipment and the costs of disposing of the consumables.

If you are considering the purchase of a complete new dust collection system, you will have control over more of these variables, such as the selection of electrical components that impact energy use. Nevertheless, even if you are simply assessing what replacement filters to use in an existing dust collector, a TCO analysis can yield useful information and surprising results.

Figure 1 (next page) is a sample dust collection worksheet used to gather TCO data. Following is a more in-depth look at some of the key items that may be included in such a worksheet and how they affect TCO.

Energy

Many factors influence a dust collector’s electrical energy consumption. Though there can be numerous electrical loads associated with a dust collector – timer boards, rotary airlock motors, etc. – the largest portion of the electrical load relates to the fan or blower required to move air through the system.

It is important to understand that differential pressure losses are directly proportional to the amount of air moved through the system, and the amount of air in turn is directly proportional to the cost of electrical energy consumed by the fan. While ducting should be optimized at the time of installation to reduce the amount of pressure loss, we will focus on the energy control devices and filters which contribute to variable pressure losses during dust collector operation.

When running a dust collector with a constant speed fan (i.e., with no energy control device), the amount of air moving through the collector will vary during the service life of the filters. Why does this occur? When filters are clean and differential pressure is at its lowest, more air blows through the system than required, essentially wasting energy. As filters become loaded with dust, static pressure is increased and less air is moved as a result. Thus, filters use more energy in the early stages of service life and less in the final stages.

One way to reduce this problem is via a mechanical damper at the blower outlet. Depending on the type of filters used, periodic adjustment of the damper to regulate airflow can save an average of 1" w.g. of static pressure over the life of the filter.

A far more effective approach is the use of a variable frequency drive (VFD) that electrically controls fan speed. When filters are new, speed is decreased to obtain the desired airflow. When filters become loaded, the fan is sped up to maintain a constant airflow. The electrical control is highly efficient in maintaining desired airflow, and energy consumption is greatly decreased. The use of a VFD has been proven to save an average of 4" w.g. of static pressure over the life of the filter. The added capital cost of installing a VFD on a dust collector will vary. However, the return on investment is typically under one year.

Additional factors that impact energy use are:
• Premium efficiency vs. standard efficiency fan motors: Industrial electric motors are the single largest consumer of electricity in the U.S. Premium efficiency motors that meet or exceed requirements of the Energy Independence and Security Act (EISA) are designed to combat the energy waste that occurs with conventional motors. Used to power a dust collector fan, a premium efficiency motor can pay for itself in reduced electrical power use and/or through rebates and incentive programs offered by many electric utilities. These motors run cooler and last longer, making them ideal for use with VFDs for optimum fan speed control and energy savings.
• Compressed air usage: The amount of compressed air required to perform pulse-cleaning of filters and maintain a lower pressure drop is important to consider. Compressed air requirements will vary significantly depending on filter design.
• CO2 emissions cost: Although this does not contribute tangibly to TCO, the amount of CO2 emissions from operation of a dust collector should be considered and stated as a cost impact on the environment.

Consumables, Maintenance and Disposal

The items in these two categories are straightforward and can be summarized as follows:
• Cartridge replacement: The amount of money spent on replacement filters alone.
• Transportation cost: The amount of money required to have replacement filters delivered to the operation site.
• Inventory cost: Typically, replacement filters are not received the day they are replaced in the system. This component is the amount of money required to carry inventory of replacement filters.
• Labor cost: The cost of labor required for maintenance personnel to change filters.
• Disposal cost: Depending upon the type of material being filtered, there is a cost associated with proper disposal of filters laden with process dust. If you are handling a hazardous dust, cartridge disposal costs may be higher. By reducing filter change-out frequency, associated disposal costs can be reduced.
• Downtime cost: This will vary from facility to facility, but it refers to the amount of time in lost production due to shutting down the collector for a filter change.

Clearly, when viewed on an annualized basis, all of these factors are largely dependent on the anticipated service life of the filter. The change-out schedule will determine how many filters you can expect to buy, transport, store and dispose, as well as the costs of labor and downtime associated with filter service.

TCO examples

The worksheet in Figure 1 compares two different filters, both containing standard media with standard cartridge filtration efficiency. Filter A, at a unit cost of $90, is a conventional dimple-pleat style cartridge filter. Filter B, at a unit cost of $120, is an open-pleat style cartridge filter designed for extended service life and lower pressure drop operation.

Figure 2, the Life Cycle Comparison Report, uses data from the worksheet in Figure 1 to project the TCO of a new 16-cartridge dust collection system equipped with Filter B. Though it has a higher initial cost than Filter A, Filter B operates at a lower pressure drop over a longer period of time to save on energy use. The Energy Category in Figure 2 shows savings achieved by combining Filter B with energy-efficient electrical components. The use of a premium efficiency motor alone yields savings over a standard efficiency motor, but the best savings by far are realized with the combination of a VFD and premium efficiency motor – nearly $12,000 in projected savings over 8760 operating hours or one year.

Filter B also offers 50 percent longer service life, which translates into an additional $764.82 savings in consumable costs and $1,712.69 savings in maintenance and disposal costs. Added to energy reductions, the total cost of ownership savings per year = $14,416.54.

As noted earlier, TCO analysis can also be helpful with existing dust collectors. This was the case in a real-life application involving the metalizing of aircraft engine parts, in which the manufacturer was experiencing problems with plugging of filter cartridges in three identical dust collectors. "Filter A" – a conventional dimple-pleat filter with fire-retardant media – lasted only about 1,000 hours, necessitating frequent replacement.

The company decided to test a comparably rated "Filter B" (i.e., same efficiency but an extended-life, low-pressure-drop open-pleat filter) in two of the three collectors. The filters lasted for 16 months or 5,280 operating hours before needing replacement. Figure 3 shows the TCO savings achieved by switching to Filter B. Based on a combination of field experience and analysis of the TCO data, the manufacturer switched all three collectors to Filter B and is now saving over $20,000 per year in maintenance and energy costs.

By now, it should be clear that the lowest-priced dust collector filter is not necessarily the most economical or the most sustainable choice. TCO provides a useful tool for comparing the real costs of operating an existing dust collector with different filters, as well as a tool for evaluating the impact of energy-saving electrical components in the design of new and refurbished dust collection systems.

Tomm Frungillo is the Vice President of sales for Latin America and focus markets for Camfil Farr Air Pollution Control (APC) Jonesboro, Arkansas

Tony Supine has held numerous positions with the company including research and development manager, technical director and currently plant manager

For Information:
Camfil Farr APC
3505 S. Airport Road
Jonesboro, AR 72401, USA
Tel. +1.800.479.6801 / 870.933.8048
Fax +1.800.222.6891
E-mail: filterman@farrapc.com
www.camfilfarrapc.com